Z06 with Nitrous guys come in (and C5's)
#1
Z06 with Nitrous guys come in (and C5's)
I sure see a lot of action with the Z06 and the spray, on this site, even more so than the vetteforum. I suppose this is cause the z06/ls6 is an absolute beast on the spray with few mods, and we have mucho nitrous action here at ls1tech. Anyway, I am putting together a Z06/spray portfolio and would like you guys to post install pics, including bottle mounts, gauge panels under hood. Even complete car pics launching, burning out or purging would be nice. I guess we could accept the C5 also, and even throw in a couple C6's. I have had a couple guys interested in spraying their C6/Z06 (one was PRO Dry, and the other PRO Plate), but no go yet, if anyone knows of the a new Z06 on the spray let them know about this thread. Thanks
Robert
Robert
#2
Robert:
I will try to get some install pics. I've really almost finished the install. I can't get 12V to the solenoids when I am in the window and at WOT
I am working on trouble shooting it but no luck so far. I'd hate to post pics of something that doesen't work.
I will try to get some install pics. I've really almost finished the install. I can't get 12V to the solenoids when I am in the window and at WOT
I am working on trouble shooting it but no luck so far. I'd hate to post pics of something that doesen't work.
#3
TECH Addict
iTrader: (21)
Join Date: Nov 2005
Location: Maine USA
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
Alrighty then...
Beers 1999 C-5 Vert
Nitro Daves LS-1 Wet Plate
DynoTune Bottle, DynoTune Bottle Accessories, DynoTune Gauges, HSW Dry Nozzles and Custom Hoses.
Hard Lines and wiring by Vin @ 860 Performance (located in New Hampshire)
Gauge Pod (Wideband not hooked up yet)
Bottle Install, custom Blanket with C-5 Logo
Interior Bottle shot
Window Switch location (Two Stage with Built in TPS)
Custom Beer Panel
Dave's Wet Plate and the Dry Lines going to the Blackwing
NX Lightning Series Stage Six Nitrous Noids
Fuel Noid covered
Fuel Noid not covered
Overall Engine Bay
Nitro Daves LS-1 Wet Plate
DynoTune Bottle, DynoTune Bottle Accessories, DynoTune Gauges, HSW Dry Nozzles and Custom Hoses.
Hard Lines and wiring by Vin @ 860 Performance (located in New Hampshire)
Gauge Pod (Wideband not hooked up yet)
Bottle Install, custom Blanket with C-5 Logo
Interior Bottle shot
Window Switch location (Two Stage with Built in TPS)
Custom Beer Panel
Dave's Wet Plate and the Dry Lines going to the Blackwing
NX Lightning Series Stage Six Nitrous Noids
Fuel Noid covered
Fuel Noid not covered
Overall Engine Bay
Last edited by Beer99C5; 05-22-2006 at 10:40 PM.
#4
Thanks Beer, now I don't have to go looking for yours. Did you have any problems with your wiring pushing your sw panel out and the tape holding? I think I am going to go to screws on the one end, this is how my last one was done, and I am always changing/adding/updating my wiring anyway so might as well make it removable.
terry s, I'll be waiting, and good luck on finding your gremlins. If I can help let me know.
Robert
terry s, I'll be waiting, and good luck on finding your gremlins. If I can help let me know.
Robert
#5
TECH Addict
iTrader: (21)
Join Date: Nov 2005
Location: Maine USA
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
Right now there is enough tension on the wires to keep the panel in place without any tape or fasteners. When I get off the rig I am likely going to drill it out and use small black screws in the corners to hold it in place.
I am likely going to get a replacement console (they are about $100) to use for making more panel designs (be a PITA getting pics with new designs now that mine is installed), so if I sell the Vette (not likely) I will have a replacement for my drilled out console. My system is designed to be removed with no signs of Nitrous being on it (have stock airbox etc.)
Got a buddy on the ship looking to get a kit for his C-5 after my stuff is finalized, he has a Vararam, will likely send him your way for a dry kit (you got the Vararam figured out).
I also have a Fuse panel mounted on the Battery compartment seperator, its not ready for photos yet, but it offers a good place to run the fuses (very accessable and right by the window switch).
Beer
I am likely going to get a replacement console (they are about $100) to use for making more panel designs (be a PITA getting pics with new designs now that mine is installed), so if I sell the Vette (not likely) I will have a replacement for my drilled out console. My system is designed to be removed with no signs of Nitrous being on it (have stock airbox etc.)
Got a buddy on the ship looking to get a kit for his C-5 after my stuff is finalized, he has a Vararam, will likely send him your way for a dry kit (you got the Vararam figured out).
I also have a Fuse panel mounted on the Battery compartment seperator, its not ready for photos yet, but it offers a good place to run the fuses (very accessable and right by the window switch).
Beer
Trending Topics
#8
TECH Addict
iTrader: (24)
Join Date: Jun 2003
Location: St Joe, MO
Posts: 2,645
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Robert56
I guess we could accept the C5 also,
TNT F1 kit jetted for 100hp when the motor started smoking
old setup
New intake and mounting
One because it's so badass
Last edited by JoeyGC5; 05-23-2006 at 07:47 AM.
#9
Originally Posted by JoeyGC5
Talk about a kick in the nuts
TNT F1 kit jetted for 100hp when the motor started smoking
TNT F1 kit jetted for 100hp when the motor started smoking
Robert
#10
TECH Addict
iTrader: (24)
Join Date: Jun 2003
Location: St Joe, MO
Posts: 2,645
Likes: 0
Received 0 Likes
on
0 Posts
It's a Greddy (ebay) can with a machined internal baffle I made. I'm also using the truck pcv valve, which has either the smaller opening or a redesigned valve, I think anyway With over 3k miles on the motor before I yanked it out, not one drop of oil.
#15
7 Second Club
iTrader: (11)
NX Shark Nozzles
SS Lines
Homebrew distributions blocks
Homebrew Fuel tank
Battery Relocated to rear, Flaming river battery cut off switch, Bottle mounted on 5/8" plywood GG down, almost done NX Heater and Bottle Blanket, SS lines to manifold with pressure and cutoff
Battery Cut off Switch
SS Lines
Homebrew distributions blocks
Homebrew Fuel tank
Battery Relocated to rear, Flaming river battery cut off switch, Bottle mounted on 5/8" plywood GG down, almost done NX Heater and Bottle Blanket, SS lines to manifold with pressure and cutoff
Battery Cut off Switch
Last edited by Phil99vette; 05-25-2006 at 09:57 AM.
#19
On The Tree
iTrader: (9)
Join Date: Jun 2005
Location: Houston, TX.
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
Here are a few pics of my NOS Plate install in my Z06. I made some custom solenoid brackets and also made the pieces for the console.
More to come soon.
More to come soon.
Last edited by Bluewire; 06-06-2006 at 09:15 PM.